Mercury 3 275 HP Outboards (1990-1993) Repair Manual Clymer Reparaturanleitung

This Mercury manual is 640 pages.

QUICK REFERENCE DATA

CHAPTER ONE / GENERAL INFORMATION
Manual organization / Notes, cautions and warnings / Torque specifications / Engine operation / Fasteners / Lubricants / Gasket sealant / Galvanic corrosion / Protection from Galvanic corrosion / Propeller / Specifications

CHAPTER TWO / TOOLS AND TECHNIQUES
Safety first / Basic hand tools / Test equipment / Service hints / Special tips / Mechanic's techniques / Specifications

CHAPTER THREE / TROUBLESHOOTING
Operating requirements / Starting system / Charging system / Ignition system / Breaker-point ignition troubleshooting (1990-1992 3 hp models) / Capacitor discharge ignition (CDI) / Direct voltage tests / Resistance test / Speed limiter / Spark advance/idle stabilizer module troubleshooting / Fuel system / Engine / Specifications

CHAPTER FOUR / LUBRICATION, MAINTENANCE AND TUNE-UP
Lubrication / Proper fuel selection / Recommended fuel mixture / Fuel mixing procedure / AutoBlend II injection system / Constant ratio oil injection / Variable ratio injection system / Lower drive unit lubricant change / Propeller shaft lube / Saltwater corrosion of gear housing bearing carrier and nut / Storage / Anti-corrosion maintenance / Complete submersion / Flushing the cooling system / Tune-up / Compression test / Spark plug plugs / Lower unit and water pump check / Fuel system service / Fuel line and hoses service / Fuel filter service / Fuel pump (all models except fuel-injected models) / Fuel pressure test / Battery and starter check / Starter solenoid check / Alternator and rectifier check / Ignition timing, synchronization and adjustment / On-boat performance test / Specifications

CHAPTER FIVE / TIMING, SYNCHRONIZING AND ADJUSTING
Ignition timing and synchronization / 3 hp models / 3 and 5 hp models / 8, 9.9 and 15 hp models / 20 and 25 hp models / 40 hp models / 50 and 60 hp models (prior to serial No. D000750) / 50 and 60 hp models (serial No. D000750-on) / 75 and 90 hp models / 100 and 115 hp models / 135-200 hp (except EFI) models / 250 and 275 hp models / 150Xri, 175Xri and 200Xri (EFI) models / Specifications

CHAPTER SIX / FUEL SYSTEM
Fuel pump / Carburetors / Throttle plunger carburetor (3 and 3.3 hp models) / Integral fuel pump carburetor (4 and 5 hp models) / Integral fuel pump carburetor (8-25 hp models) / WMA carburetor (40 hp models) / MerCarb center bowl carburetor (50 and 50 hp models prior to serial No. D000750) / WME carburetor (50 and 60 hp serial No. D000750-on, 75, 90, 100 and 115 hp models) / WMH carburetor (135-200 hp models) / MerCarb center bowl carburetor (250 and 275 hp models) / Thermal air valve (135-200 hp models) / Enrichment valve and choke solenoid systems / Anti-siphon devices / Fuel filter / Fuel tank / Fuel hose and primer bulb / Electronic fuel injection (EFI) / Fuel management tests / Specifications

CHAPTER SEVEN / IGNITION AND ELECTRICAL SYSTEMS
Battery / Battery charging system / Starting system / Magneto breaker point ignition / Capacitor discharge ignition (CDI) (1993 3.3 hp models) / Capacitor discharge ignition (CDI) (4-275 hp models) / Specifications

CHAPTER EIGHT / POWER HEAD
Engine serial number / Gaskets and sealants / Fasteners and torque / Power head / Specifications

CHAPTER NINE / LOWER UNIT GEAR HOUSING
Service precautions / Gear housing / Water pump / Bearing carrier and propeller shaft / Pinion gear, drive shaft and forward gear / Lower shift shaft, bushing and cam / Pinion depth/gear backlash / Propeller / Trim tab adjustment / Specifications

CHAPTER TEN / POWER TRIM AND TILT SYSTEM
Manual tilt assist system / One-ram integral power trim system (40-60 hp models) / Three-ram integral power trim system (75-200 hp models) / One-ram oildyne power trim system (250-275 hp models) / Power trim assembly removal/installation / Power trim motor and pump assembly removal/installation / Specifications

CHAPTER ELEVEN / OIL INJECTION SYSTEM
Autoblend II (50 and 60 hp prior to serial No. D000750) / Constant ratio oil injection (40 hp and 50-60 [serial No. D000750-on] hp models) / Injection system service / Variable-ratio oil injection (75-115 hp models) / Warning horn system / Injection system service / Variable-ratio oil injection (V6 models) / Warning hose system / Injection system service / Specifications

CHAPTER TWELVE / MANUAL REWIND STARTERS
3 and 3.3 hp models / 4 and 5 hp models / 8, 9.9, 15, 20 and 25 hp models / 40 hp models / Specifications

Clymer Reparaturanleitungen zählen zu den erfolgreichsten auf dem Markt und sind sowohl für Hobbyschrauber als auch für Mechaniker der unverzichtbare Ratgeber bei allen Fahrzeugreparaturen. Pflegen, warten, reparieren - alle Arbeiten sind detailliert beschrieben und durch viele Abbildungen erläutert.

Written from hands-on experience gained from the complete strip-down and rebuild of the car, Clymer can help you understand, care for and repair your car. We do it ourselves to help you do-it-yourself, and whatever your mechanical ability, the practical step-by-step explanations, linked to over 900 photos, will help you get the job done right. Regular servicing and maintenance can help maintain its resale value, save you money, and make it safer to drive.

Sprache: Englisch

Gerne stellen wir Ihnen beim Kauf dieses Artikels das 32-seitige technische Wörterbuch von Haynes (englisch/deutsch) als Download zur Verfügung.